228 terms every guitarist should know.
A
- Abalone
- A highly colorful shell material commonly used on guitar inlays. Abalone inlays come in a rainbow of colors and can appear to change color when viewed from different angles.
- Accelerando
- To play with increasing speed. A gradual increase in speed.
- Acoustic Guitar
- A hollow body guitar that produces sound using only the strings and soundboard instead of an amplifier.
- Action
- The height of the strings above the fret board.
- Active Electronics
- Mainly used on bass guitars, active electronics on the pickup use a battery to modify the signal for higher output and clearer sound.
- Alnico
- Magnetic alloy comprised of aluminum (Al), nickel (Ni), and copper (Co) used to make electric guitar pickups.
- Altered and Open Tunings
- The result of changing the tuning of one or more strings from standard EADGBE.
- Alternate Picking
- A guitar playing technique that employs strictly alternating downward and upward picking strokes in a continuous run.
- Alternating Bass
- A style of playing where the right hand alternates between two or more strings.
- Amplify
- Increasing the volume of an instrument.
- Arch Top (Carved Top)
- Refers to the body of a guitar that has been carved or shaped for either the tone or looks of the guitar.
- Arpeggio
- A chord played one note at a time. A broken chord, usually played evenly low to high and back again.
- Arrangement
- The setting of an original or standard tune for a given solo instrument or group of instruments.
- Artificial Harmonic
- Hold down a note on the neck with left hand, and use the right hand to lightly touch a point on the string, then pluck the side of the string that is closer to the bridge.
B
- Bakelite
- Early form of plastic used in some guitars from the 30's to the 50's.
- Bar
- A sub division of time in music.
- Bar Line
- A vertical line which shows the end of a bar of music.
- Barre Chord
- The technique of placing the left hand index finger over two to six strings in the fingering of a chord. The great advantage of using barre chords is that they are ‘moveable shapes.’
- Bass-Strum Style
- A right hand technique which involves picking a bass note then strumming the rest of the chord.
- Beam
- A horizontal line which shows two eighth or sixteenth notes belonging to the beat shown on the bottom of the time signature.
- Beat
- A sub division of time usually felt as the pulse within a piece of music.
- Bending
- The act of pushing or pulling a string sideways across a fret to raise the pitch of a note by a half to full tone or more.
- Bigsby
- Term used for a simple non recessed vibrato developed by Paul Bigsby.
- Binding
- A protective and decorative strip made of wood or plastic that is placed along the outer most edges of the top, back, neck, fingerboard and sometimes headstock.
- Block Markers
- Square, rectangular or shark tooth inlays marking fingerboard position.
- Body
- The main part of a guitar (not the neck). Usually where the bridge and tailpiece are located.
- Bolt-On Neck
- Attaching the guitar neck to the body of the guitar with bolts. The screws or bolts are attached with a neck plate in the back of your guitar.
- Bookmatched
- Wood coming from the same tree and actually being one piece of wood that has been cut into consecutive slices so the grain in the panels creates mirror image patterns.
- BPM
- Beats per minute, or tempo. Defines the ‘click speed’ of the metronome.
- Brace
- Braces are wooden struts glued inside hollowbody guitars providing strength and affecting tone quality.
- Bridge
- The bridge is located on the body of the guitar and transfers sound from the strings to the body of the guitar.
- Bridge Pin
- Slotted plugs that help hold guitar strings in place on some instruments.
- Bullet
- Name given to the appearance of truss-rod adjustor nut on the headstock of some Fender guitars.
C
- CAP
- Also called a capacitor, a common electrical component that stores up an electrical charge generally used on the tone potentiometer on electric guitars.
- Capo
- A mechanical barre that attaches to the neck of a guitar by means of a string, spring, elastic or nylon band, or a lever and thumbscrew arrangement.
- Celluloid
- A common plastic material used on guitar pickguards, tuners and binding. This material is not very durable and deteriorates over time.
- Center Block
- A solid wood block running through the body of a semi-acoustic guitar body.
- Checking
- Cracking found in lacquer finished guitars. Vintage guitars often have checking in their lacquer finishes.
- Chicken Picking
- A combination of right hand pick and fingers, usually associated with country music.
- Chicken Scratching
- The strings are being ‘scratched’ (strummed) with the pick, while the left hand is damping the strings (touching the strings lightly).
- Chord
- A group of three or more notes played simultaneously.
- Chord Chart
- A diagram which shows a chord progression.
- Chord Progression
- A sequence of chords played one after another.
- Chorus (of a tune)
- The portion of a song lyric or melody that is repeated, often with other voices joining in.
- Chromatic Scale
- A scale containing all twelve notes within an octave, with each fret on the guitar moving up one half-step.
- Chromatics
- 12-note scale including all the semitones of the octave.
- Closed Voicing
- Placing the member notes of a chord as close together as possible, no matter the inversion.
- Coil Tap
- Switch used to break up a humbucker into single coil sounds or vice versa.
- Coils
- Wire is wrapped around a nonconductive material.
- Count In
- A count at the start of a piece of music to show when to start and how fast to play.
- Cutaway
- A concave area generally in the upper right bout of a normal right-hand guitar that allows the player easier access to the high frets.
D
- Dog Ear
- Nickname for a P-90 style pickup with mounting ears.
- Dot Neck
- Guitar with simple dot inlays in the neck position markers.
- Double Bar Line
- Two vertical lines which show the end of a section or piece of music.
- Double Stop
- Two notes played simultaneously.
- Down Stroke
- Right hand movement from top to bottom.
- Dreadnought
- Generally associated with C.F. Martin and their biggest and loudest acoustic guitar.
- Dropped-D Tuning
- The practice of lowering the sixth string (E) by a whole tone, one octave lower than the fourth string.
E
- Electric Guitar
- A guitar which can be electrically amplified (usually with a solid body).
- Electro Acoustic
- An acoustic guitar with a built in pickup, often a piezo electric pickup.
- End Block
- Usually glued to the top, back, and sides at the bottom end of the guitar. Often strap buttons are anchored into this block.
F
- F-Hole
- Sound hole carved into instruments.
- Feedback
- Created by amplified sound re-entering the amplification system, eventually creating oscillation that produces a loud pulsing noise or squeal.
- Finger Picks
- Banjo-style picks that fingerstyle guitarists use when playing steel-string instruments.
- Fingerstyle
- Playing with the fingernails or fingertips with or without fingerpicks as opposed to playing with a flatpick.
- Finish
- The protective coating covering the guitar, often paint or lacquer.
- Fixed Bridge
- Non-vibrato bridges.
- Flame
- Maple with dramatic grain resembling flames. Sometimes also called Flame Top.
- Flat
- Lower in pitch.
- Flat Top
- Used to refer to an acoustic guitar with a flat (non-arched) top.
- Flatpick
- A triangular or teardrop-shaped piece of nylon or plastic used to pluck or strum guitar strings.
- Footstool
- A small adjustable stool used to raise the height of the guitar.
- Four/Four Time
- A time signature of four quarter beats in one bar of music.
- Fret Board / Fingerboard
- The area on top of the neck that you would press the string upon to create a note or frequency.
- Fret Marker
- Any marking on the fretboard to assist the guitarist to quickly locate a particular fret.
- Fretless
- A fretboard with no frets. Usually found with basses and gives a smooth sound.
- Frets
- The metal strips along your fretboard. They come in a variety of sizes.
- Fretting
- Placing a finger next to a fret.
G
- Gig
- When a band plays a show at a venue.
- Guitar Strings
- Strings for electric and steel string acoustic guitars are very similar, but cannot be used interchangeably.
- Guitar Tablature
- A system of reading and writing guitar music (abbreviated to TAB).
H
- Half Beat
- A beat twice as long as a quarter beat.
- Hammer-On
- A note sounded literally by ‘hammering’ down with a left hand finger, often performed in conjunction with a note first plucked by the right hand.
- Hang Tag
- Small tags and cards hung on guitars in show rooms. A hang tag for a vintage guitar is generally very difficult to find.
- Hard Tail
- Term used to describe an electric guitar without a vibrato bridge.
- Hardware
- Refers to different parts of a guitar including jacks, bridge, tuners, and more.
- Harmonic Tones
- Certain places along a guitar string where you can produce multiple tones, located directly above the fret wires at the 5th, 7th, and 12th frets.
- Harmonics
- Chime-like sounds achieved through natural or artificial methods involving touching strings at specific points.
- Harmonize
- To bring two or more notes together in harmony.
- Harmony
- Two or more notes sounding simultaneously.
- Headstock
- The part of the guitar where the strings attach to the tuners. Also called a peghead.
- Heel
- Portion of neck where the neck curves or is reduced to join the body.
- Hexatonic Scale
- A scale with six notes per octave (a pentatonic scale has five notes per octave).
- Hollow Body
- An electric guitar body style with a thin body similar to an acoustic guitar.
- Humbucker
- 2 single coil pickups, side by side, and wired so that the electronic hum you get with most single coil pickups is canceled out.
- Hybrid Picking
- The pick is used in combination with finger(s).
I
- In Tune
- A note is in-tune when it matches the pitch of another note in the manner it is supposed to.
- Inlay
- Markers on your fretboard that give players a frame of reference.
- Interval
- The distance between two notes.
- Intonation
- The ability of your instrument to play and hold the correct note.
- Inversion
- Structuring a chord with a note other than the root as the lowest note.
J
- Jackplate
- Mounting plate for output jack.
L
- Laminated
- The backs, sides and even tops of some instruments can be made from several pieces of wood which have been laminated to form one piece.
- Lead Guitar
- The part played by a guitar soloist in a rock band.
- Legato
- Obtained on the guitar by using strictly hammer-ons and pull-offs.
- Locking Nut
- Bolts that lock the strings in place at the nut.
- Logo
- The manufacturer's brand name or trademark usually on the headstock.
- Luthier
- A guitar maker and guitar repair expert.
M
- Machine Heads
- Used for tuning up each string and housed on the headstock (sometimes referred to as tuning heads or tuning keys).
- Major Chord
- The combination of the first, third and fifth notes of a scale.
- Melody
- A succession of musical notes played one after another (usually the most recognizable tune of a song).
- Modulate
- To change keys within a piece of music.
- Mother of Pearl
- Type of inlay using a form of shellfish material.
N
- Neck
- The part of a guitar which houses the fret board. The neck is sort of the middle of the guitar.
- Neck Block
- Found inside of the body at the base of the neck. The neck block provides a strong point to mount the neck to the body.
- Neck Pickup
- Refers to the pickup closest to the neck.
- Neck Plate
- A metal plate used in the Fender style bolt on designs.
- Neck Press
- Uses gentle heat and pressure to straighten a neck. Can be tricky and should only be performed by a trained luthier.
- Neck Reset
- Performed to restore the correct angle between the fingerboard and bridge which provides the correct action needed to play the guitar.
- Note
- A note is defined by its frequency: the speed of vibration of the sound producing device.
- Nut
- Piece of plastic or metal between the headstock and fretboard. Guides the strings from the headstock and tuners over the fretboard.
- Nylon String Guitar
- An acoustic guitar which has three nylon strings.
O
- Octave
- Eight notes in sequence. Technically, an octave is any two tones with frequency ratios of either 2-to-1 or 1-to-2.
- Open
- A string played with no left hand fingers fretting any note.
- Open Chords
- These chords usually contain open strings (not fretted with left hand). Often the first kind of chords the beginner will learn.
- Open Voicing
- A manner of chord construction in which the member notes are broadly separated.
- Out of Tune
- Anything not ‘in tune’ is, by definition, ‘out of tune.’
P
- P I M A
- Letters derived from the Spanish names for the fingers of the right hand: pulgar (thumb), indice (index), medio (middle), and anular (ring).
- P-90
- Refers to an early Gibson single coil pickup.
- PAF
- Refers to a sticker on Gibson pickups.
- Palm Mute
- The string(s) is being damped with right hand palm, close to the guitar's bridge.
- Passive
- Usually describes a guitar that does not use pickups which require power (active pickups).
- Pedal Tones
- Notes that constantly repeat in a pattern. This technique is favored by neoclassical guitarists such as Yngwie Malmsteen, Vinnie Moore etc.
- Peghead
- A peghead is where the tuners are mounted, also called a headstock.
- Pentatonic Scale
- A five-tone scale used often in rock.
- Pickguard
- Piece of material placed on the body of the guitar to protect from pick scratches.
- Picking
- Plucking or producing a sound on the guitar in general, either with the fingers or a flatpick.
- Pickups
- An electromagnet housed underneath the strings on an electric guitar which produces a signal to be amplified by a guitar amplifier.
- Pinch Harmonic
- The thumb slightly catches the string after it is picked, creating a high pitched sound in any position.
- Pitch
- The frequency generated by a vibrating string. For example, the frequency of the Concert-A note is 440Hz.
- Plectrum
- A small triangular shaped piece of plastic used for striking the guitar strings with the right hand. Another name for a flatpick.
- Positions
- A reference to placement of the left hand index finger at various frets.
- Pot
- A potentiometer mounted to the body of an electric guitar commonly used for control of volume and tone.
- Power Chord
- A chord consisting of the first (root), fifth and eighth degree (octave) of the scale.
- Pre-Bend
- The note is bent before it is struck with the pick.
- Pre-CBS
- Refers to Fender guitars manufactured before the 1965 takeover of Fender by CBS.
- Pull-Off
- The opposite of a hammer-on. Performed by plucking a note with a finger on a higher note and pulling parallel to the fret.
Q
- Quarter Beat
- A sub division of time in music twice as long as an eighth beat.
- Quilted
- Describes beautiful undulating pattern found in wood, generally refers to maple.
R
- Refin
- Refers to a refinished guitar. Refinished guitars have a significantly lower value than an original guitar with the original surface.
- Refret
- Also called a fret job, refers to re-fretting a guitar.
- Relative Pitch
- The comparison of one pitch to another.
- Relief
- The upward arching bow in an instrument's neck that allows the strings to move without touching the frets.
- Repeat Sign
- Two dots placed before a double line indicating the repeat of a section of music.
- Rhythm
- A sequence of events played with the right hand on a guitar which gives a piece of music a distinct beat.
- Rhythm Guitar
- Rhythmic strumming of chord backup for a lead player, singer, or ensemble.
- Rhythm Notation
- A system of reading and writing music which shows rhythm.
- Ritardando
- Achieved by gradually delaying or slowing down the tempo.
- Root
- The first note of a scale. A chord is named for its root, even if the root is not actually played.
- Rosette
- A decorative pattern around the sound hole. It is purely decorative.
- Rout
- A hole or cavity cut into a guitar, often the body of the guitar.
S
- Saddle
- The rigid bar at the opposite end of the strings from the nut. The saddle is located near the base of the guitar.
- Scale Length
- Length of the vibrating string from nut to saddle, or twice the distance from the nut to the 12th fret.
- Scalloped Fretboard
- When the fret board has been carved out to create a scoop between frets.
- Set Neck
- When a neck is glued into the neck pocket of the body of a guitar.
- Setup
- The adjustment of the action of a guitar for optimal playing characteristics.
- Sharp
- Higher in pitch.
- Shuffle
- A rhythm of which each main beat is divided into three smaller beats (prominent in blues music).
- Single Coil Pickup
- Usually thinner sound than humbucker, used in most Fender guitars.
- Six String
- Shorthand for a guitar that has six strings.
- Slide
- A plastic or glass tube placed over the third or fourth finger of the left hand and used to play ‘slide’ or glissando effects.
- Slur
- To glide over (a series of notes) smoothly without a break.
- Soap Bar
- Nickname for a P-90 style pickup that has no mounting ears.
- Solid Body
- Refers to electric guitars with a solid (non-hollow) body.
- Sound Hole
- The hole in the front of an acoustic guitar body from which the sound is projected.
- Spaghetti Logo
- Early style Fender logo with letters resembling spaghetti.
- Split Coil
- A double coil pickup wound with multiple coils that are smaller than a standard 2 coil pickup.
- Staccato
- Obtained on the guitar by using strictly alternate picking.
- Standard Tuning
- A six-string guitar tuned to E-A-D-G-B-E, or a bass tuned to E-A-D-G.
- Steel String Guitar
- An acoustic guitar which has all steel strings (usually four wound and two plain ones).
- Stem
- The vertical line in music or rhythm notation which appears above or below a note or rhythm.
- Stop Tailpiece
- Has slots in it to hold string balls in place. Usually used with a tune-o-matic bridge.
- Strap
- Used to hold the guitar while in standing position.
- Strap Pin
- A secure button for attaching a guitar strap. These are almost always metal.
- String Winder
- A swivel device with a handle with a fixture that fits over the tuning keys.
- Strings
- Stretched between the tuners and the body. Different string weights give different sounds or frequencies.
- Strumming
- A technique where the right hand plays the notes of a chord simultaneously either with down or up strokes.
- Sustain
- The duration of sound from one or more strings.
- Sweeping
- The pick is swept through the strings in a downward or upward motion.
- Swing
- A rhythm in music in which the down beat is felt slightly longer than the up beat.
- Syncopate
- To modify the rhythm by stressing or accenting a weak beat (purposely playing off beat).
T
- T-Frets
- Refers to the shape of the metal fret. T-Frets are used in most refrets.
- Tablature or Tab
- A system of writing music for fretted instruments whereby a number or letter appears on lines representing the strings.
- Tailpiece
- On instruments without bridge pins the strings are commonly anchored to a tailpiece.
- Tapping
- The use of right hand fingers on the fretboard.
- Tempo
- The speed of a piece of music.
- Thinline
- Term used to describe hollow body electric guitars, first used with the Gibson Byrdland guitar.
- Three Quarter Beat
- A beat which is one and a half times as long as a half beat.
- Three-Quarter Guitar
- A smaller than normal guitar with shorter strings and less space between frets.
- Three/Four Time
- A time signature of three quarter beats in one bar of music.
- Through Neck
- A thru-neck design uses a neck that actually runs right through the center of the body.
- Thumbwheel
- A small wheel used on adjustable bridges to adjust the bridge's height.
- Tie
- A curved line which shows two notes of the same pitch joined together and played as one.
- Time Signature
- A sign at the beginning of a piece of music (looks like a fraction) which shows how many beats in each bar and how long each beat lasts.
- Tone
- The combination of pitch, volume, sustain and sound character produced by a particular guitar or guitar equipment.
- Transcription
- To write a solo, note for note, off of a recording.
- Transpose
- To change the key of a piece of music by a specific interval.
- Trapeze Tailpiece
- This tailpiece design has a hinge-like mechanism on it and has a shape similar to a swinging trapeze.
- Tremolo
- A technique performed with either a very rapid down-up movement of the pick or a rapid plucking of the fingers.
- Triad
- A three-note chord.
- Triple Stop
- Three notes played simultaneously.
- Truss Rod
- A curved metal bar implanted into the neck of a guitar used to adjust the amount and direction of bend in the neck.
- Tube (Valve)
- ‘Tube’ is the U.S.A. slang term for ‘electron tube’. Tubes are glass enclosed devices that modify and/or amplify input signals.
- Tune-O-Matic Bridge
- Attached to guitar's body by two posts and has adjustable saddles.
- Tuner
- An electronic tuning device.
- Tuning
- Adjusting the tuning keys until a particular string vibrates at the correct frequency.
- Tuning Key
- A knob used to tighten or loosen a string.
- Tuning Machines
- Mechanical devices used to increase or decrease string tension. Located on the guitar headstock.
- Twelve/Eighth Time
- A time signature of twelve eighth beats in one bar of music.
U
- Up Stroke
- Right hand movement from bottom to top.
V
- Veneer
- Refers to thin wood or plastic laminate used in the construction of some guitars.
- Verse
- The lyrics/melody portion of a song that tell the flowing story.
- Vibrato
- To vibrate by slightly altering a pitch higher and lower.
- Voicing
- The arrangement of the member notes of a chord.
- Volute
- A piece of wood installed just behind the peghead. It strengthens the neck where the headstock begins.
W
- Waist
- Part of the body of a guitar which is smallest in dimension from top to bottom.
- Whammy Bar
- Used to stretch the strings on a tremolo or vibrato system.
- Whole Beat
- A beat in music which lasts for a whole bar in music with a time signature of four/four.